20 Myths About Change Door Lock: Dispelled

Reasons to Change Door Lock

There are many reasons to change door lock, from upgrading your home's security to redecorating your entryway. You may need to change locks if your key gets stuck or is difficult to turn.

Even DIY beginners can easily alter their locks. To start, gather the materials you need.

Take off the lock that was previously used.

Before installing a new lock, it is necessary to remove the old lock from the door. This is essential when you suspect that someone else may have a key to the house. It is also an ideal option if you have moved into a house that was burglarized, or welcomed a new roommate. It is easier than you think and can be completed in a matter of minutes.

Start by removing the screws holding the deadbolt faceplate onto the door frame. You'll have to take off the screws on both sides of the door in order to remove the faceplate. This will allow you see what's behind it and provide you with a better understanding of how to continue with the next steps.

After removing the old faceplate, you must remove the bolt, strike plate and the strike plate. Use a screwdriver or a wrench to loosen the bolt and then remove it from the hole in the door. If the bolt is rusted you may need to use a chisel to hit it. If you're using a chisel, you must be careful not to scratch the door frame.

Make sure your new deadbolt, doorknob and lock will fit in the holes already in the door before removing the old one. Most hardware stores and big box stores carry several different types of locks and will help you find the right one for your needs. Get help if the lock you purchased doesn't fit your door.

While you're taking off the lock that was previously in use, look for small notches or depressions in the handle or around the trim. If you are able to locate them, use a straightened safety-pin or flat screwdriver in order to remove the handle.

Once the screw inside the handle has been removed you can now begin to remove the knob from its spindle. To do this, locate the set screw on the base of the knob and loosen it. Then, you'll need to remove the knob from the spindle. Finally, carefully remove the spindle from the door.

Install the new lock

It's a great idea to change the locks on your doors frequently, especially if you have had a break-in. It is easy, cheap and effective to change the lock on your door. The majority of people can do it by themselves using a screwdriver, a screwdriver, and some basic instructions. You may also want to learn how you can change the key on your door lock to ensure that only you hold the key.

You'll need to buy a new lock that has the same keyway as your existing lock. You can save money if you change the lock's key yourself. The majority of locksmiths charge a fee for this. You can buy a new lock from a hardware store or on the internet. A standard deadbolt will typically fit on most doors however, you'll have to measure the size of your door to ensure that it will fit.

The majority times, your new lock will come with the cardboard template that will show the way it will fit on the door. This template can be used to drill the hole. It's much simpler than having to measure every time. If the template does not exactly match your hole, bring it back to the store and get another one.

You must install the new lock on the right-hand side of the door. You can verify this by checking the latch, which ought to be labeled "up" or something similar. Make sure the latch is properly seated in the plate and then attach it using the supplied screws.

When replacing a knob lock, you should also be aware of the handing. Most knob locks are left-handed, however there are a few that are right-handed. If you're not careful, you could place the knob on the wrong side of the door, which could prevent you from locking it from inside or outside.

You should try the new lock after you have completed. You should be able to lock and unlock the door with keys from inside as well as from the outside. If you're not happy with the outcome then you can always call an expert locksmith to fix it.

Test the lock

A door lock that will not open can be a hassle but it can also put the safety of your family at risk. It's a good thing that it's simple to fix the majority of issues with door locks by performing a bit of troubleshooting and lubrication. First, make sure that your key is correctly cut and that the lock isn't soiled or loose. If this doesn't solve the issue, try to lubricate the door lock actuator using powdered graphite or a silicone-based grease.

Then, make sure that the door lock switch, the wiring harnesses and the actuator connector are all functioning correctly. To check this, consult the manual or wiring diagram to determine the purpose and color-coding of all door lock switch wires. Use a digital meter, or test light to determine if the actuator is receiving power and ground when the switches are activated. If you observe a voltage toggle with each switch activation, that means the switches are working and it's most likely the actuator that requires to be replaced.

If the switch appears to work but the actuator does not move when you turn it, there may be a problem with the cylinder. The actuator cylinder is equipped with pins that are spring-loaded. They prevent the cylinder from moving until the key is put in, which then pushes them up to meet the height of the key at the location. This causes the cylinder eventually to rotate and open the lock body and allowing the handle latch.

If your door lock actuator is faulty, you can remove the switch and wires from the actuator by using small screwdrivers to unlock the locking bolt and separate the plastic cover that holds the electrical connector. Then, disconnect the door lock actuator and let it fall. Then, you should be able to find the two bolts in 10mm that keep the actuator in place and remove them. Once the actuator is removed, you will be in a position to disconnect the black electrical connector and then pull it out along with the actuator and lock assembly.

Replace the key

If your deadbolt is locked or door knob isn't working, you'll have to reset it or replace it. This isn't difficult and will save you money. But, before doing this it is a good idea to get a locksmith to examine the locks and check for any problems. This will give peace of mind knowing that your home is secure and safe.

To begin, remove the exterior faceplate from the doorknob or deadbolt. There could be screws that hold it in place, if so use a screwdriver to loosen them, and then pull the faceplate off. Next, use a flat head screwdriver to remove the interior faceplate. Once you have removed your faceplate, you can remove the bolt and screw from inside the lock cylinder.

A locksmith can decide whether you require a replacement or rekey the lock. They can also advise you on the best security options for your home. They can also make any needed modifications to the door and frame to ensure that it is a perfect fit. They will also offer an assurance on their work.

If you choose to rekey your lock, you'll need to purchase the new key. It is crucial to select the lock key that is fitted snugly. A key that is not the right size may damage the internal mechanism of the lock and prevent it from functioning. Insert the key into the lock to test its size. If the key is completely against the plug then it's the correct size. If  double glazing window locks repairs  extend out from the top of the plug, they're too long.

You may want to change the lock on your door for a variety of reasons, such as:

If you're moving into a former homeowner's house or have lost keys, rekeying the lock can be a more affordable alternative than replacing it. It's also less expensive than a complete replacement. Rekeying an existing lock might not be possible in certain circumstances. For example, if the lock is damaged or has been repeatedly jammed, it's probably time to replace it.